Design and Calculation of a Concrete Mixer (100 kg)
Design and Calculation of a Concrete Mixer (100 kg) Min Min Shwe Sin. Department of Mechanical Engineering . Technological University (Taunggyi), Southern Shan State, Myanmar . Abstract- In this paper describe the design and calculation of concrete mixer for weight 350 kg approximately. A concrete mixer
THE CALCULUS OF THE MIXING ROTATING DEVICES SHAFTS BASED ON ...
Keywords: mixing rotating device shaft; strength calculation; principle of critical energy. 1. Introduction The mechanical design of the mixing rotating devices which operate in liquid medium depends on the exact determination of the mechanical and hydrodynamic loadings of the mixing device (shaft and mixer). These loadings are
Industrial Mixer Shaft Design - ProQuip Inc. Mixing Solutions
The design of the industrial mixer shaft must be able to handle the torque and bending moment induced by its impeller. Modern designs for industrial mixer impellers often put more stress on the mixer shaft caused by bending moment than the stress caused by the torque required to power them.
Design, Modification and Analysis of Concrete Mixer Machine
Abstract:- This paper contains the study, design, modification and analysis of concrete mixer. Mixer widely used to make a concrete mixture which used to building construction and industry to make a concrete block, pipe, sheets, etc. it is observed that there is a failure of shaft and blade in mixer thus, deign modification and analysis of ...
Mechanical design does not end with the shaft, since strength and practical issues remain for the impeller. Another part of mixer design is the tank in which the mixer is used, since tank dimensions inﬂuence mixer features, especially shaft length. Conversely, a mixer requires tank features, such as bafﬂes, support strength, and other tank ...
Design And Fabrication Of Portable Concrete Mixture Machine
So in this project I am trying to identify the different causes of blade and shaft failure.In this project with the title “design and fabrication of portable concrete mixer machine”, we were planning for design and fabrication of a concrete mixer. This project brought advantages over manual mixing and expensive mechanized concrete mixer.
design, the impact of decisions made at the process design step on the mechanical design requirements must be understood. The second step in the design sequence is the mechanical design of the mixer components. The fundamental approach is straight-forward, design for power (torque and speed), then shaft loads, and finally mixer dynamics.
The concrete mixer machine should be of the following; i. Low in price ii. High and small in size iii. Easy to operate iv. Easy to maintain v. Have readily available spare part vi. Marketable 2.11Portability and Space The concrete mixer machine is design in such a way that it can easily be carried from one place to the other. It
Basic Concrete Mix Design Materials Pounds of material S.G. Abs Volume 667 3.15 X 62.4 Cement 667 3.15 3.39-Total Cementious 667 Miller Stone 1590 2.6 9.80 Evert Sand 1242 2.65 7.51 Water 300 1 481 1590 2.60 X 62.4 1242 2.65 X 62.4 4.81 Air 5.5% 1.485 Total 3799 27.00 w / cm 0.45 Unit Wt. 140.72 Basic Concrete Mix Design Materials Pounds of ...
Design and Calculation of a Concrete Mixer (100 kg) – IJERT
Design and Calculation of a Concrete Mixer (100 kg) Design and Calculation of a Concrete Mixer (100 kg) Min Min Shwe Sin Department of Mechanical Engineering Technological University (Taunggyi), Southern Shan State, Myanmar. Abstract- In this paper describe the design and calculation of concrete mixer for weight 350 kg approximately.
Fabrication and Design of Efficient Concrete Mixer Machine
The design and drafting of all components of concrete mixer is done by Auto CAD software. The result obtained in this particular work shows that the compressive strength of brick is sufficiently high if it is produced by concrete mixer. Keywords-Design, concrete mixer, Compressive strength, fabrication, mixing volume 1. INTRODUCTION
HOW TO CALCULATE OUTPUT OF A CONCRETE MIXER? - CivilBlog.Org
May 10, 2014 · In addition, it depends upon the duration of mixing, supply of materials to the mixer and the speed at which charging and discharging operations are carried out. Sometimes the speed of transporting concrete from mixer to the formwork limits the output of a mixer. The following example illustrates the calculation of output of a mixer per day.
Concrete formworks are subjected to various loads and pressure. Concrete formwork loads and pressure calculations are described in this article. Formworks or molds are considerably important for building constrictions by holding fresh concrete mixture at place until it get required strength by which the self weight can be sustained. Generally, there are various loads which are […]
How to Design a Drive Shaft - Drive Shaft Design for a ...
Shaft is a basic mechanical component. The concept of drive shaft design formula is explained in this article with an example shaft design problem.You can see a shaft in almost every machine, which has rotating parts. Typically a shaft has circular cross section. However, shaft with other cross sections find special application. We will discuss the design concept of a drive shaft subjected to ...
6.8 Mounting of radial shaft seal on shaft 59 . 6.9 Radial shaft seals under the pressure 59 . 6.10 Frictional loss 59 . Chapter 7 60 . V-BELT DRIVES (Basis data and calculation in accordance with . PN-M-85203: 1967)
Batching, Mixing, Transporting, and Handling Concrete, Chapter 10
2. Shrink-mixed concrete is mixed partially in a sta-tionary mixer and completed in a truck mixer. 3. Truck-mixed concrete is mixed completely in a truck mixer (Fig. 10-6). ASTM C 94 (AASHTO M 157) notes that when a truck mixer is used for complete mixing, 70 to 100 revolutions of the drum or blades at the rate of rotation designated by
13 Types of Concrete Mixer Machines You Need to Know - Civil ...
Horizontal Shaft Mixer. Features: This is a Compulsory Concrete Mixer. Due to its horizontal design, the paddle mixer can easily mix a series of a wide range of aggregates especially the massive ones to create a more uniform slurry. Well suited for lightweight as well as dry hard concrete.